The influence of sputtering targets on the manufacturing costs and efficiency of CIGS
The sputtering process is the most important technique for material deposition in CIGS-manufacturing. With innovative sputtering targets CIGS producers can significantly reduce their production costs.
Manufacturers of sputtering targets like PLANSEE have two approaches to reduce CIGS module manufacturing costs: In order to lower the material consumption by a better target utilization PLANSEE introduced the new monolithic and dogbone rotary target designs. With MoNa the company offers a new material alloy that increases conversion efficiencies.
(firmenpresse) - Changing the sputtering system from planar to rotary targets increases the target utilization from about 30 to 75%, which saves expensive raw material. Depositing the molybdenum back contact by monolithic molybdenum rotary targets - which are completely made of molybdenum - gives additional benefits: The expensive bonding of the molybdenum material on a stainless steel backing tube is not required. In addition, a higher sputtering power of up to 30 kW/m can be applied. This creates a very high heat load which cannot be accommodated by bonded-type targets: Indium is used as bonding material which melts at only 156 °C thus the risk of de-bonding is eliminated with monolithic targets. A higher sputtering power results in a higher deposition rate and improved thin film properties, e.g. higher electrical conductivity.
In contrast to the high lateral homogeneity of thin films deposited by sputtering, a sputtered target has generally an erosion profile which is not homogeneous – a result of different plasma densities. As a consequence, the targets have to be replaced even if there is sufficient material on most of the target area. To overcome this limitation, targets with varying outer diameter (named “dogbone” for rotary targets) or thickness is a solution to extend the target lifetime and increase the target exchange interval.
Two elements have a big impact on the CIGS cell efficiency: iron (Fe) and sodium (Na). Whereas iron degrades the cell performance by introducing defects in the CIGS structure, sodium has the opposite effect: It concentrates defects at grain boundaries, which is a requirement for achieving high efficiencies.
Low iron levels are only achieved by a high purity of the primary materials as well as a high quality manufacturing process. Especially for molybdenum targets the iron content can vary significantly. The traditional way to introduce sodium into the CIGS absorber is by means of a soda-lime-glass substrate. During the manufacturing process sodium diffuses from the glass through the molybdenum back contact into the absorber layer, resulting in a sodium concentration in the order of 0.1 at%. However, reproducibility and lateral homogeneity of this process is low, and flexible substrates do not act as sodium source.
Solar cell producers now have an easy alternative at hand: By sputtering a layer of sodium doped molybdenum, the amount of sodium in the absorber layer can precisely be controlled and reproduced. PLANSEE offers MoNa sputtering targets with high purity and a uniform and fine grained microstructure. Tests in cooperation with the Swiss EMPA institute have already proven their benefits in practice: With sodium doped molybdenum layers the efficiency of CIGS solar cells could be significantly improved.
Themen in dieser Pressemitteilung:
Unternehmensinformation / Kurzprofil:
PLANSEE is a world-leading manufacturer of products made from refractory metals and metallic composite materials. The privately owned company has been manufacturing innovative powder-metallurgically processed high-performance materials for over 90 years, and covers the whole production process, right from the raw material to the finished product. The company employs materials experts, product developers and local technical sales staff to provide customers all over the world with all the help and assistance they require.
PLANSEE SE
Nadine Kerber
nadine.kerber(at)plansee.com
Datum: 26.01.2012 - 14:58 Uhr
Sprache: Deutsch
News-ID 108096
Anzahl Zeichen: 3383
contact information:
Kategorie:
Solar energy
Typ of Press Release: Produktinformation
type of sending: Veröffentlichung
Diese Pressemitteilung wurde bisher 484 mal aufgerufen.
Die Pressemitteilung mit dem Titel:
"The influence of sputtering targets on the manufacturing costs and efficiency of CIGS"
steht unter der journalistisch-redaktionellen Verantwortung von
Plansee SE (Nachricht senden)
Beachten Sie bitte die weiteren Informationen zum Haftungsauschluß (gemäß TMG - TeleMedianGesetz) und dem Datenschutz (gemäß der DSGVO).
