HSM exhibits extensive range of baling presses at IFAT in Munich
(PresseBox) - From 30 May to 8 June 2016, HSM GmbH + Co. KG, the south German manufacturer of baling presses, PET solutions and document shredders, will present its extensive range of products at IFAT, the world?s leading trade fair for water, sewage, waste and raw materials management, in Munich in Hall C1, booth 251/350.
Besides one of the smallest fully automatic channel baling presses (HSM VK 1005), there will also be an exhibition of one of the largest (HSM VK 12018 R FU). In this way, visitors to the exhibition can get a good impression of the broad range from the manufacturer.
The HSM VK 1005 is suitable for industrial volumes with smaller to medium-sized volumes of material with a throughput of up to around 1 ton per hour. In combination with the HSM DuoShredder 5750, a two-phase, fully automatic shredding system, the baling press becomes a complete waste disposal system. Using the DuoShredder, documents can first be destroyed at security level P-4 (according to DIN standard 66399) and then pressed into bales weighing up to 120 kg by using the HSM VK 1005 with a press force of 110 kN.
The fully automatic channel baling press HSM VK 12018 with a frequency-controlled drive saves up to 40 % energy. This drive makes a significant contribution to environmental protection and efficiency. Using this, up to 40 % of energy costs can be saved. This drive is available as an option for many HSM baling presses and multi-phase shredding systems. With the HSM VK 12018, up to 44 tons of mixed paper, weighing around 1 ton each, can be pressed every hour using a drive of 2 x 55 kW and a press force of 1,200 kN. With foil, the bales reach around 700 kg. However, it is not only the weight, but also the quality of the bale that is crucial for the disposer. The more densely the bales are pressed, the more stable they are for storage indoors or outdoors, and they then fulfil the requirements of paper mills better. Another decisive criterion for disposal is the size of the bale. With 1.10 x 1.10 m, they offer the best size for the truck load and save approximately 1/3 of the wire compared to smaller presses.
HSM is also presenting its wide range of products in the field of vertical baling presses. Four machines with between 120 kN press force (HSM V-Press 610) and 548 kN press force (HSM V-Press 1160) can be visually inspected on site by the specialist visitors. HSM has developed an energy-saving drive, the ?rapid? technology, especially for the vertical balers series V-Press. This technology reduces the power consumption and cycle time by up to 40 % compared to conventional drives - while increasing the throughput at the same time. An additional cylinder in the centre runs alone with press plate idling and a low press force requirement. Only with high back pressure, are the two outer cylinders connected. Due to the special pump technology, the baling presses are particularly quiet.
HSM trade fair booth at IFAT 2016: Hall C1, Booth 251/350
Datum: 23.05.2016 - 08:23 Uhr
Sprache: Deutsch
News-ID 472775
Anzahl Zeichen: 3060
contact information:
Town:
Frickingen
Kategorie:
Tradeshows
Diese Pressemitteilung wurde bisher 440 mal aufgerufen.
Die Pressemitteilung mit dem Titel:
"HSM exhibits extensive range of baling presses at IFAT in Munich"
steht unter der journalistisch-redaktionellen Verantwortung von
HSM GmbH + Co. KG (Nachricht senden)
Beachten Sie bitte die weiteren Informationen zum Haftungsauschluß (gemäß TMG - TeleMedianGesetz) und dem Datenschutz (gemäß der DSGVO).
