How to Make a Wooden Cutting Board in 6 Measures
Using board butter can help keep your wooden cutting board in the best possible condition for many years to come. Read on to discover why board butter is a necessary step in the maintenance of your cutting board as well as other wooden kitchen tools.
(firmenpresse) - This project is often a great one for cooks who want a long-lasting butcher block cutting board that will not warp more than time or move as they use it. An added bonus is definitely the curved notch at one end that permits you to scrape food in the cutting board directly into your bowl.
Step 1: Make a decision around the design, dimensions and supplies you'll be using for the cutting board. Assemble the essential tools and supplies. Considering the fact that you will be using various power tools, you'll want to put on safety glasses. Also, possess a face mask for after you sand the cutting board.
Step 2: Assemble the butcher block. Reduce three 17-inch lengths of 2-inch thick clear maple on the miter saws. NOTE: These are straight cuts, not miter cuts.
Alternate the wood grain by flipping the middle board more than in order that its grain runs counter to the outer two boards. Apply wood glue towards the edges in the board where they are going to join. Clamp them together while the glue dries.
Step 3: Smooth the butcher block. Use a belt sander to flatten the cutting board surface so there is certainly no noticeable ridge/transition from board to board. To perform this, 1st move the sander across the boards within a diagonal motion. When the transition is smooth, sand using the grain along the length of your boards.
Switch to a random orbit sand and to progressively finer grades of sand paper until the surface of the cutting board has no discernible texture.
Trim one end of the board on a table saw. Spot the board in a wooden cradle that holds the wood steady as you slide it in to the blade. Cut only a thin strip off the end, to smooth the edges of your 3 boards you glued collectively. Establish which side of your board will probably be the prime - commonly the surface together with the additional desirable wood grain.
Step 4: Notch the cutting board. Flip the board so the bottom side faces upward and draw a semicircle in the unfinished end using a compass and pencil.
Pass the board via the band saw and reduce along the semicircle tracing. Add a drum sander for your drill press and smooth away any saw marks along the curved vertical edge from the circle.
Install a rabbeting bit with ball bearing guides on your router. The bit will reduce a recess into the bottom edge on the semicircle even though leaving a collar of wood on the major surface. Turn the board bottom side up and route along the edge to kind the recess. The recess will permit a bowl of a specific dimension to slide in to the board without gaps and to catch the food.
Step 5: Add legs towards the chopping block. Drill four legs sockets into the bottom of your cutting board, using a drill press. Do not drill via the board. Place a socket at each and every corner around the flat end with the board, about 1/2 inch off the long as well as the short sides. Align the two sockets about 1/2 inch in the lengthy side in the board, but inset them about two inches from the brief side to supply clearance for the semicircle and recess.
Coat the interior in the leg sockets with glue. Tap in short wooden dowels for the legs. Make sure that the dowels are identical in length and tap them in to the same depth so the board will stand levelly.
Step 6: Finish the surface. Add a mineral oil coating to guard the board from food and liquids. Sand the mineral oil into the board using No. 400 wet and dry sandpaper.
Unternehmensinformation / Kurzprofil:
Datum: 15.02.2022 - 04:36 Uhr
Sprache: Deutsch
News-ID 655248
Anzahl Zeichen: 4069
contact information:
Kategorie:
Business News
Typ of Press Release: please
type of sending: don't
Diese Pressemitteilung wurde bisher 116 mal aufgerufen.
Die Pressemitteilung mit dem Titel:
"How to Make a Wooden Cutting Board in 6 Measures"
steht unter der journalistisch-redaktionellen Verantwortung von
sirrsfurniture.com (Nachricht senden)
Beachten Sie bitte die weiteren Informationen zum Haftungsauschluß (gemäß TMG - TeleMedianGesetz) und dem Datenschutz (gemäß der DSGVO).
