Cables for parking brake and clutch actuation

Two rather unassuming, but important wear parts

(PresseBox) - When you think about typical wear parts in the vehicle, it is not usually the cables that come to mind first. But both the cables for the parking brake and the cable for clutch actuation can corrode or wear during a vehicle's service life. They have to be replaced in this case. We are also prepared for this repair case and offer cables for parking brakes and clutch actuation in our Jakoparts range specialised in Asian vehicles.

Clutch cable

The clutch cables are subjected to constant high tensile loads when operated, making them a typical wear part. To prevent excessive wear or, in the worst case, a break in the cable, they must be checked and replaced if necessary. Professional installation is important here, as incorrectly installed or incorrectly adjusted clutch cables present a problem and can cause increased wear on the clutch. A typical example are rotating clutches, i.e. they cause the clutch lining to burn on the clutch disc or the flywheel to overheat.

Parking brake cable

The task of the parking brake is to protect the vehicle against rolling away or to act as an auxiliary brake. The parking brake function is based on the continuous actuation of the rear brake, this is carried out either mechanically by hand or foot actuation, or electrically. It works by permanently locking the vehicle?s wheels. If the effect of the hand brake reduces, a worn hand brake cable is a likely cause. It is possible that the wheels may no longer be blocked correctly after the hand brake is actuated. This is often caused by a corroded or worn hand brake cable. As a classic wear part, it can be replaced easily and at a relatively low cost. However, if the hand brake cable turns out to be intact, it may also be necessary to reset it depending on the condition of the brake pads or brake shoes. This would restore the full function of the hand brake. A well-adjusted hand brake should be able to be tightened in four stages.

Clutch cable

Article number: J230*

Parking brake cable

Article number: J392*

Please note that the picture is only for web! For printable images please contact Ms. Kipphan:

anika.kipphan(at)herthundbuss.com

Weitere Infos zu dieser Pressemeldung:
Unternehmensinformation / Kurzprofil:
Bereitgestellt von Benutzer: PresseBox
Datum: 22.09.2020 - 09:00 Uhr
Sprache: Deutsch
News-ID 619809
Anzahl Zeichen: 2348

contact information:
Town:

Heusenstamm

Kategorie:

Pharmaceuticals & Biotech

Diese Pressemitteilung wurde bisher 207 mal aufgerufen.


Die Pressemitteilung mit dem Titel:
"Cables for parking brake and clutch actuation"
steht unter der journalistisch-redaktionellen Verantwortung von

Herth+Buss Fahrzeugteile GmbH&Co. KG - English press compartment (Nachricht senden)

Beachten Sie bitte die weiteren Informationen zum Haftungsauschluß (gemäß TMG - TeleMedianGesetz) und dem Datenschutz (gemäß der DSGVO).

Oil-stop cable solves a familiar problem at Mercedes-Benz ...

The problem is a common one: As the result of a design flaw, oil is able to infiltrate the length of the harness and reach the control unit due to the capillary effect (which describes how liquids spread out in tight gaps, tubes and pipes). Here, ind ...

Diagnosis on demand ...

With our innovative new diagnostic solution Diagnosis on Demand, we take over at the point where independent workshops often reach their limits. With Diagnosis on Demand VCI (Vehicle Communication Interface), dealers and workshops are offered the per ...

Herth+Buss company blog drive! ...

In our company blog drive!, we have been focussing on topics relating to car and transport from various perspectives since April 2017. With the selection of focus topics, drive! is now summing up the past three and a half years and focussing on the c ...

Alle Meldungen von Herth+Buss Fahrzeugteile GmbH&Co. KG - English press compartment